Beta Address: http://blish.org/sdrdxdoc/changes212.html
| in 2.12z, and (FSK USB and FSK LSB) added to demodulator modes. In addition, TCP/UDP interface will now send modes 8 and nine for these settings. Note that you may have to reduce the demod bandwidth, quit, and restart for these to work for the first time. |
in 2.12z, ^ PgUp and ^ PgDn now adjust CWO in 1 Hz increments. |
| in 2.12z, T re-purposed for transmit command. ⇑ T is now the Toggle Notch command. |
| in 2.12y, added to linearize various scope spectrum data |
| in 2.12x, Saved baseband files header change from Wave to WAVE |
| in 2.12v, WFM button on UI, but WFM still under development. Disabled. |
| in 2.12v, added (Demod markers On Waterfall) |
| in 2.12v, added +/- 9 KHz tuning buttons for Euro BCB signals |
| in 2.12t, the button arrangement has been modified to add one more row of buttons on the right side of the panel. This is to accommodate some new functionality, beginning with . |
| in 2.12t, additional support for servers (very much still beta) |
| in 2.12t, (GRid Numbering) added. Useful when SdrDx is monitoring IF instead of the airwaves; allows the grid to exist without incorrect nomenclature. |
| in 2.12t, (Save Audio palette) and (Edit Audio Palette) added. |
| in 2.12s, (Load Audio Palette) added, gives you control over the palette for the audio waterfall in the scope. Along with this, SdrDx will automatically load pal_defaulta.wfp from the home directory on startup into the audio palette. Use the usual and to create these palettes. |
| in 2.12r, Swap checkmark in →Right-click dialog now also swaps I/Q for network connected devices. This allows operation with radio IF systems that are of odd parity, that is, where USB looks like LSB and tuning runs backwards. |
| in 2.12r, CW demodulator envelopes now adjust to 1500 Hz per side |
| in 2.12r, Demodulator envelope now adjusts in 50 Hz steps |
| in 2.12r, 32 MHz limit on tuning removed for all SDRs that had it |
| in 2.12r, changed to (keyboard lock) |
| in 2.12q, ⇑ PGUP ⇑ PGDN affects volume |
| in 2.12q, AFEDRI 16 level gain implemented |
| in 2.12q, a checkbox to select pre- or post-s-metering added |
| "Missing Pkts" message changed to "MP" |
| Scope mode y position control for both channels via right click |
| Andrus MK 1.5 SDR support added to 400 KHz, Ch A, also autofind |
| AFEDRI support added to 1.25 MHz, also autofind |
Grid spacing (  GS ) now variable from 2-20, read out in status bar 1 |
| SDR Not Connected message changed to RFSPACE not connected (2.12h) to reduce confusion with other SDR types. |
| fix for FCDP+ being unable to select 190 kHz (2.12f) |
| Red arrow indicates SDR center tuning at base of waveform area (2.12e) |
| ^ D allows tweaking of S meter calibration. A setting of 499 is calibration that matches RFSPACE SDRs. Other settings may be used to adjust for FCD, etc. |
| FCD Pro plus support. First, the FCDP+ has to be attached to a USB port. Right-click on the FCD button, there should be a checkbox that says "FCDP+"; CHECK that box, then in the same dialog, under OSX set the sample rate to 50000, under Windows set the sample rate to 48000. Close the dialog by clicking OK. Go to the SDR button at the lower left, left click, set the dialog bandwidth / sample rate there to 50 KHz. Close the SDR dialog with OK. The FCD button should now be colored green; LEFT click on it. With QT 4 under Windows, only low samples rates (48 khz or less) are possible with the FCDP+. |
| now offsets the frequency readout for legibility. |
| 2500 hz and 3000 hz steps added for Griffin Powermate |
2.12z Fixes
| in 2.12z, , , , , and tooltips fixed |
| in 2.12w, Tooltip nomenclature for +/- 9 KHz buttons fixed |
| in 2.12u, an FM demodulator crash was fixed |
| (2.12a) 16.6 MHz limit for FCDP+ fixed |
| toc | index | guide | changes | keyboard | , previous | . next |